Aluflex

Product description

Aluflex is an aluminium pigmented paint based on a flexible penetrating alkyd oil.

image

Recommended use

For use in cargo holds and on areas where a thorough pretreatment cannot be carried out. Aluflex penetrates porous surfaces.

 

image

 

Film thickness and spreading rate 

                                                                           Minimum                  Maximum               Typical

Film thickness, dry (µm)                                  20                              50                            25

Film thickness, wet (µm)                                 50                            120                            60

Theoretical spreading rate (m²/l)                  20                              8                               16image

Physical properties

Colour Aluminium

Solids (vol %)* 40 ± 2

 

Flash point 38ºC ± 2 (Setaflash)

VOC 438 gms/ltr UK-PG6/23(97). Appendix 3

Gloss Flat

Water resistance Fair

Flexibility Good

*Measured according to ISO 3233:1998 (E)

Surface preparation

All surfaces should be clean, dry and free from contamination. The surface should be assessed and treated in accordance with ISO 8504.

Bare steel

Remove heavy rust scale.

Coated surfaces

If applied on top of old coating systems (i.e. epoxy or polyurethane), it may be necessary to abrade the surface.

Other surfaces

The coating may be used on other substrates. Please contact your local Jotun office for more information.

Condition during application

The temperature of the substrate should be minimum 3ºC above the dew point of the air, temperature and relative humidity measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure correct drying.

Application methods

Spray Use airless spray or conventional spray

Brush Recommended for stripe coating and small areas, care must be taken to achieve the specified dry film thickness.

Roller May be used. However when using roller application care must be taken to apply sufficient material in order to achieve the specified dry film thickness.

Application data

Mixing ratio (volume) Single pack.

Thinner/Cleaner Jotun Thinner No. 2

Guiding data airless spray

Pressure at nozzle 15 MPa (150 kp/cm², 2100 psi.).

Nozzle tip 0.38 - 0.53 mm (0.015 - 0.021").

Spray angle 60 - 80°

Filter Check to ensure that filters are clean.

Drying time

Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will be affected correspondingly. The figures given in the table are typical with:

  • Good ventilation (Outdoor exposure or free circulation of air)

  • Typical film thickness

  • One coat on top of inert substrate

Substrate temperature

5°C

10°C

         23°C

40°C

Surface dry

2 h

2 h

1 h

1 h

Through dry

20 h

10 h

8 h

2 h

Dry to recoat, minimum

12 h

9 h

6 h

4 h

The given data must be considered as guidelines only. The actual drying time/times before recoating may be shorter or longer, depending on film thickness, ventilation, humidity, underlying paint system, requirement for early handling and mechanical strength etc. A complete system can be described on a system sheet, where all parameters and special conditions could be included.

Typical paint system

 

Aluflex

1 x 25 µm

(Dry Film Thickness)

Touch-up

Aluflex

1 x 35 µm

(Dry Film Thickness)

Full coat

 

Other systems may be specified, depending on area of use

Storage

The product must be stored in accordance with national regulations. Storage conditions are to keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed.

Handling

Handle with care. Stir well before use.

Packing size

20 litre container.

Packing may vary from country to country according to local requirements.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not breathe or inhale mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Скачать: 
.