Jotaproof Topcoat

Product description

Jotaproof Topcoat is a two-pack acrylic, isocyanate free topcoat with excellent gloss and colour retention.

Recommended use

As topcoat over an epoxy/epoxy mastic system where a durable, high gloss finish is required in aggressive atmospheric exposure. Cures at low temperatures.

Film thickness and spreading rate

                                                                         Minimum                Maximum                Typical

Film thickness, dry (µm)                               60                              125                         75

Film thickness, wet (µm)                              95                              200                        120

Theoretical spreading rate (m²/l)              10,5                             5                            8,4

Physical properties

Colour According to colour card and Multicolor tinting system (MCI)

Solids (vol %)* 63 ± 2

Flash point 31ºC ± 2 (Setaflash)

VOC 310 gms/ltr UK-PG6/23(97). Appendix 3

Gloss Glossy

Gloss retention Excellent

Water resistance Very good

Abrasion resistance Very good

Solvent resistance Very good

Chemical resistance Very good

Flexibility Very good

*Measured according to ISO 3233:1998 (E)

Surface preparation

All surfaces should be clean, dry and free from contamination. The surface should be assessed and treated in accordance with ISO 8504.

Coated surfaces

Clean, dry and undamaged compatible primer. Contact your local Jotun office for more information.

Other surfaces

The coating may be used on other substrates. Please contact your local Jotun office for more information.

Condition during application

The temperature of the substrate should be minimum 5°C and at least 3°C above the dew point of the air, temperature and relative humidity measured in the vicinity of the substrate. Good ventilation is required in confined areas to ensure correct drying.

Application methods

Spray Use airless spray

Brush Recommended for stripe coating and small areas, care must be taken to achieve the specified dry film thickness.

Application data

Mixing ratio (volume) 4:1

Mixing 4 parts of Comp. A (base) to be mixed thoroughly with 1 part Jotaproof TC, Comp.

B (curing agent).

Pot life (23°C) 3 hours (Reduced at higher temp.).

Thinner/Cleaner Jotun Thinner No. 26

Guiding data airless spray

Pressure at nozzle 15 MPa (150 kp/cm², 2100 psi).

Nozzle tip 0.33-0.46 mm (0.013-0.018").

Spray angle 40-80°

Filter Check to ensure that filters are clean.

Drying time

Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will be affected correspondingly. The figures given in the table are typical with:

• Good ventilation (Outdoor exposure or free circulation of air)

• Typical film thickness

• One coat on top of inert substrate

1. The surface must be free from any chalking or any other contamination and if necessary, sufficiently roughened prior to application.

The given data must be considered as guidelines only. The actual drying time/times before recoating may be shorter or longer, depending on film thickness, ventilation, humidity, underlying paint system, requirement for early handling and mechanical strength etc. A complete system can be described on a system sheet, where all parameters and special conditions could be included.

Note: To obtain full coverage an extra coat may be necessary, especially for signal colours in red, orange and yellow.

Other systems may be specified, depending on area of use

Storage

The product must be stored in accordance with national regulations. Storage conditions are to keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed. Shelf Life Comp. A: 2 years

Shelf LIfe Comp. B: 1 year

Handling

Handle with care. Stir well before use.

Packing size

20 litre unit: 16 litres Comp. A (base) in a 20 litre container and 4 litres Jotaproof TC, Comp. B (curing agent) in a 5 litre container

or

5 litre unit: 4 litres Comp. A (base) in a 5 litre container and 1 litre Jotaproof TC, Comp. B. (curing agent) in a 1 litre container

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not breathe or inhale mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.